| Shear Knives and
Spacers Model 583/683 |
| For male shear knife
and holders, specify: |
| Part
Number |
Description |
| 683950 |
15/16" (24 mm) wide for
clamping to the male knife shaft. |
| Spare
parts for the 683950 male knife holders |
| 683001 |
Male knife |
| 683065 |
Garter Spring |
| 112183 |
Retainer Ring
Sprirolox |
| Model 583
female shear knives 3.150" OD (80 mm) and spacers for 2.362" (60 mm) diameter
female knife shafts as follows: |
| For inch widths
specify: |
| 583001 |
3/8" wide female shear
knife |
| 583002 |
0.0625" (1/16") female
spacer |
| 583009 |
1/8" wide female
spacer |
| 583004 |
1/4" wide female
spacer |
| 583011 |
5/16" wide female
spacer |
| 583005 |
1/2" wide female
spacer |
| 583006 |
5/8" wide female
spacer |
| 583017 |
3/4" wide female
spacer |
| 583061 |
1 7/8" wide female
spacer |
| 583007 |
1" wide female
spacer |
| 583008 |
2" wide female
spacer |
| For millimeter widths
specify: |
| 583054 |
10 mm wide female
knife |
| 583037 |
2 mm wide female
knife |
| 583038 |
3 mm wide female
knife |
| 583055 |
4 mm wide female
knife |
| 583039 |
5 mm wide female
knife |
| 583056 |
7 mm wide female
knife |
| 583040 |
10 mm wide female
knife |
| 583041 |
20 mm wide female
knife |
| 583042 |
50 mm wide female
knife |
|
| Model 683
Shear Knives and Spacers for 45 mm (1.771") Knife Shafts |
| Part
Number |
Description |
| Male
knife holder assemblies: |
| 683900 |
3 15/16" OD x 1.771" ID x
0.250" wide. Must be stacked on knife shaft. |
| 683937 |
3 15/16" OD x 1.771" ID x
0.281" wide. Must be stacked on knife shaft. |
| 683901 |
3 15/16" OD x 1.771" ID x
1.000" wide. Must be stacked on knife shaft. |
| Note: |
The
0.250",0.281" and the 1.000" series knife holders are designed to be used with
the knife spacers and are lapped to width, calibrated, etched to the width to
the nearest 0.0001". These holders when used with the female knives and spacers
listed below will produce a knife to knife width tolerance within 0.001". If
this accuracy is not required, use male knife assembly # 683950. |
| 683950 |
3 15/16" OD x 1.771" ID x
15/16" (24 mm) wide retaining ring (Spirolox). |
| 683001 |
Male knife
only |
| 683065 |
Garter spring |
| 112183 |
Ratainer ring
(Spirolox) |
| 683021 |
Ratainer ring |
| Female
Knife-Solid |
| 683005 |
2.758" OD x 1.771" ID x
1/4" wide |
| 683004 |
2.758" OD x 1.771" ID x
1" wide |
| Precision
Knife Spacers Hardened and Ground |
| 683015 |
2.758" OD x 1.771" ID x
1/16" wide |
| 683016 |
2.758" OD x 1.771" ID x
1/8" wide |
| 683017 |
2.758" OD x 1.771" ID x
3/16" wide |
| 683018 |
2.758" OD x 1.771" ID x
1/4" wide |
| 683020 |
2.758" OD x 1.771" ID x
1/2" wide |
| 683029 |
2.758" OD x 1.771" ID x
1" wide |
| Plastic
Shims for use with Model 683 Knives and Spacers |
| 683007 |
2.437" OD x 1.781" ID x
0.002" thick |
| 683008 |
2.437" OD x 1.781" ID x
0.003" thick |
| 683009 |
2.437" OD x 1.781" ID x
0.005" thick |
| 683010 |
2.437" OD x 1.781" ID x
0.010" thick |
| 683011 |
2.437" OD x 1.781" ID x
0.015" thick |
| 683012 |
2.437" OD x 1.781" ID x
0.030" thick |
|
| Model 783
Shear Knives and Spacers for 60 mm (2.362") Knife Shafts. |
| Male
Knife Holder Assembly for Stacking with Spacers on the Male Knife
Shaft. |
| 783923 |
4 1/8" OD x 2.362" ID x
0.250" wide with a Belleville washer. |
| 783902 |
4 1/8" OD x 2.362" ID x
0.375" wide with a Belleville washer. |
| 783903 |
4 1/8" OD x 2.362" ID x
1.000" wide with a Belleville washer. (this holder can also be clamped to the
shaft). |
| Male
Knife Assemblies for Clamping to the Shaft (Cannot be stacked). |
| 783983 |
4 1/8" OD x 2.362" ID x
15/16" (24 mm) wide with a Belleville washer. |
| 783984 |
4 1/8" OD x 2.362" ID x
15/16" (24 mm) wide with a garter spring. |
| 783
Series Male Knife Assembly Spare Parts. |
| 783036 |
Male knife, standard
(dished with notch) |
| 783186 |
Male knife
(hollow-ground) |
| 783618 |
Male knife - same as
#783036 (except D2 steel). |
| 783083 |
Belleville washer (0.022"
thick) |
| 783703 |
Male knife - same as
#783036 (but flat gound). |
| 783022 |
Belleville washer (0.040"
thick) |
| 783594 |
Garter spring (only used
on coil spring type holders). |
| 112632 |
Shim, steel for male
knife holders |
| 101981 |
Rataining
ring |
| Female
Knives, Standard |
| 783155 |
3.575" OD x 2.362" ID x
1/4" wide |
| 783006 |
3.575" OD x 2.362" ID x
3/8" wide |
| 783003 |
3.575" OD x 2.362" ID x
1" wide with set screw for clamping on shaft. |
| Precision
Knife Spacers for Male/Female Shafts |
| 783118 |
3.575" OD x 2.362" ID x
1/16" wide |
| 783013 |
3.575" OD x 2.362" ID x
1/8" wide |
| 783014 |
3.575" OD x 2.362" ID x
3/16" wide |
| 783015 |
3.575" OD x 2.362" ID x
1/4" wide |
| 783017 |
3.575" OD x 2.362" ID x
1/2" wide |
| 783021 |
3.575" OD x 2.362" ID x
1" wide |
| 783041 |
3.575" OD x 2.362" ID x
2" wide |
| Plastic
Shims for use with #783 Knives and Spacers |
| 783008 |
3.250" OD x 2.375" ID x
0.002" thick |
| 783009 |
3.250" OD x 2.375" ID x
0.005" thick |
| 783010 |
3.250" OD x 2.375" ID x
0.010" thick |
| 783011 |
3.250" OD x 2.375" ID x
0.015" thick |
| 783012 |
3.250" OD x 2.375" ID x
0.030" thick |
| Millimeter Widths |
| 783983 |
105 mm x 60 mm x 24 mm
wide male knife holder with Belleville washer. Must be clamped to the
shaft. |
| 783984 |
105 mm x 60 mm x 24 mm
wide female knife with a gerter spring. Must be clamped to the
shaft. |
| 783394 |
25 mm wide female knife
with set screw for clamping to the shaft. |
| 783586 |
2 mm wide knife
spacer |
| 783260 |
3 mm wide knife
spacer |
| 783261 |
4 mm wide knife
spacer |
| 783262 |
5 mm wide knife
spacer |
| 783587 |
7 mm wide knife
spacer |
| 783264 |
10 mm wide knife
spacer |
| 783265 |
20 mm wide knife
spacer |
| 783392 |
50 mm wide knife
spacer |
|
|
Model 841/883 Male Shear Knife Holder Assembly With Recommended
Spare Parts |
 |
| 841915 |
Left hand male knife
holder assembly for dovetail mounting. minimum slit width 2", includes #783036
dished male knife. |
| 841919 |
Right hand male knife
holder assembly for dovetail mounting. Minimum slitr width 2". |
| Parts for
Model 841915 or 841919 |
| 815295 |
Spring |
| 841006 |
Bracket |
| 815290 |
Clamp |
| 815291 |
Dovetail
bracket |
| 102726 |
Jergens |
| 115636 |
Light hex nut |
| 112000 |
Bearing (2) |
| 841073 |
Knife axle |
| 101329 |
Truarc 5000-137 retaining
ring |
| 101981 |
Spirolex RS-314 retaining
ring |
| 841147 |
Guard |
| 783083 |
Belleville washer,
standard, 0.022" thick. |
| 783036 |
Male knife (only),
standard. |
| 841072 |
Knife holder, body only
(holds 783036) |
| 111996 |
Washer, steel (bearing
sep.) 13/16" OD x 1/4" ID x 0.062" thick. |
| 841/883
Style Shear Cut Accessories |
| Male
Knife Assemblies (with Belleville Washer) |
| Part
Number |
Mounting |
Uses Knife
# |
Min. Slit
Width |
| 841919 RH |
Dovetail bar |
783036 |
2" |
| 841915 LH |
Dovetail bar |
783036 |
2" |
| 883909 (dual hand). Can be used
LH or RH by reversing the plate. Not usually used with 841 style
knives. |
Dovetail bar |
883010 |
1" |
| Male
Knife Assemblies (with Garter Spring) |
| 841927 RH |
Dovetail bar |
783036 |
2" |
| 841926 LH |
Dovetail bar |
783036 |
2" |
| Male
Knife Only |
| 883010 |
Single bevel |
4.156" OD x 1.125" ID x
0.062" thick. For use on 883 style male holders. |
| 783036 |
Spare knives |
4.156" OD x 3.192" ID x
0.093" thick dished. For use on 841 style holders. |
| Female
Knives for 841 Style Knife Shaft |
| 841010 |
4.995" OD x 4.001" ID x
1" wide |
| 841071 |
4.995" OD x 4.001" ID x
2" wide |
| Knife
Spacers for 841 Style Knife Shaft |
| 841013 |
4.995" OD x 4.001" ID x
1/8" wide |
| 841012 |
4.995" OD x 4.001" ID x
1/4" wide |
| 841011 |
4.995" OD x 4.001" ID x
1/2" wide |
| 841017 |
4.995" OD x 4.001" ID x
1" wide |
